Downey-Plumbing FAQ

We gathered most question asked by our clients. Check our plumbing FAQ here.

What Plumbing Service I Can DIY And I Should Call Professional Plumber?

  • Call Pro if the cable or electricity is involved. If you don’t have experience with cables and electricity, don’t put yourself, your family or home at risk. Bring licensed and bound professionals who know the cables.
  • DIY if your tub or sink is clogged. Pull the outlet plug and feed the spout snake under the pipe. If you don’t have one, straighten the clothes hanger. Rotate the instrument of your choice and release it slowly, chances are that your hair will close and accumulate. Repeat this process several times, then continue with the drain and hot water cleaner.
  • Call Pro if your pipe freezes. Trying to dilute your own pipe, you run the risk of further damage. Professional plumbers are trained to properly close cracks in the pipe.
  • DIY if your toilet overflows. Behind the toilet, near the floor, there is a water cutoff valve. Turn to the right to keep the water from rising higher. Open the tank and lift the floating ball to give it time to flow.
  • Call Pro if your backup toilet is stubborn. The problem might lie deeper in the drain, which might require some digging to fix it. Before you tear your page, make a call.
  • DIY if your sink stopper breaks, leaving your sink full of dirty water without a way to drain it. Don’t be afraid: there is a lever under the sink that controls the stopper. The pivot bar connects the water channel to the handle. Press down on the end of the rod near the handle to lift the plug. After your sink is drained, don’t hesitate to find a cheap stopper replacement.
  • Call Pro if the part needs to be replaced. If something complicated like a water heater or a water pump doesn’t work, it can mean you need a new part of it.

What Is The Solution of Frozen Pipes?

  • First thing before doing anything, turn off the water supply to the plumbing section (or the whole house if it’s the only choice) because the real problem starts after liquefaction.
  • That’s because frozen water might act as a plug, preventing water from spilling from cracks in your pipe. When the plug is thawed, water spurts out.
  • Prepare mops, buckets and towels in case there is a pipe leak.
  • Use a heater, a heat lamp, or a hair dryer to melt a frozen pipe.
  • Wrapping a frozen pipe with a heat band that is thermostatically controlled (from $ 50 to $ 200, depending on the length) is also an effective way to quickly dilute the problematic place.
  • Do not melt the pipe using a propane torch, which presents the risk of fire.

What Type of Water Heater I Should Choose?

Before you choose your heat water types, you must answer this question to decidee which one types will fit in. Question likes :

  • Which of the following best describes your climate?
  • How many people live in your household
  • Your water heater is currently supported by …
  • How do you describe the quality of your water?
  • How important is it for you that buying your new tool helps reduce your electricity bill?
  • How much are you willing to spend up front for a new water heater?
  • How long do you anticipate staying in your current home?

By answers that question you easily can choose types of your water heater :

  • Water Heater Storage Tank
  • Tankless Water Heaters
  • Hybrid / Hot Pumps

How to Fix Low Water Pressure?

Usually, low water pressure is a problem with only one fixture and is the result of mineral buildup. Mineral deposits look like white, off-white, or blue-green crust which can be seen in pipes or outside of water equipment in their joints.This deposit can be easily cleaned by doing these steps:

  • First take a clean cloth
  • Soaking a clean cloth in white vinegar and wrapping it around the affected area.
  • Secure the fabric with a rubber band and let it sit for one hour.
  • The sink and shower faucets and outdoor taps contain a section called an aerator, a net-like cover that combines air with water to create a spark-free flow. These parts can be removed and soaked in equal parts with white vinegar and water to remove mineral buildup.

How to Get Rid Roots in Drain?

Tips to get rid of roots in your drain are:

  • The first way to get rid of the root of your toilet is to pour some sodium chloride or copper sulfate, or rock salt, into the toilet covered with roots, chemical reactions will help drain your toilet clean from the roots.
  • In addition, you can also use this method by using a foamy root killer, in addition to cleaning the roots, this method also helps prevent the roots from growing back in your pipe to do this process once a year to prevent the roots from growing back.

The above 2 methods are very effective for cleaning and maintaining the cleanliness of your toilet from the roots. In addition, these compounds are also very effective in sucking moisture from the roots.

How to Remove Grease Drain?

How to remove your grease drain :

  • Boil water and mix 1 part hot water and 1 part vinegar.
  • Pour the mixture into your kitchen drain and let it sit for a few minutes.
  • Hot water will help melt the oil, while vinegar will eat the oil attached to the pipe.
  • After pouring the mixture of hot water and vinegar into the drain, follow it with boiling water. Boiling water must water the remaining oil from your pipe.
  • Clogged drains can emit a terrible odor that tends to be left in your kitchen for some time.
  • To neutralize the odor that comes from your sewer, mix 1 part hot water and 1 part bleach, then pour the mixture into the drain. Continue with warm soapy water.
  • Ways to deal with oil in your sewer must make everything flow again. Remember to take steps to prevent future blockages.

How Much Average Of Plumbing Cost Per Service?

The average commercial plumber costs around $45 to $200 per hour and a housing plumber is $175 to $450 per hour. Fixed Plumber Plans will charge you based on the type of service as a task they have done. An hourly plumber will charge based on the total number of hours needed to complete the work.

Why Do I Need a Repiping?

You will need Repiping because:

  • Leaking

Once the pipe starts to leak, this is usually a sign that your pipe is starting to wear out and they need to be replaced as soon as possible. Pipes leaked so badly to the point that they started to get holes because the metal was very thin in the areas. When a pipe starts to leak, you can usually expect most of the pipes in your home to follow.

  • Water changes

When water from your side starts to look strange, it is usually caused by severe rust in your pipe. This can actually be a health hazard and you should not drink water. Replace your pipe as soon as possible because you can expect a bigger problem to begin immediately.

  • Lower Water Pressure

Another sign that your pipe is damaged and needs to be replaced is if you see a lack of water pressure from what you saw in the past. Your pipes may be rusty, making it difficult for water to pass through, or they may collapse on their own. Don’t wait to replace the pipe if this happens!

  • Wall Damage

If the walls or parts of your house are seriously damaged, your pipes will definitely be affected. They will also suffer damage, and most people will only replace their pipes at that time instead of waiting for them to be damaged. Sometimes, this damage can even cause intense vibrations that break some of your pipes into impact.

  • Preparing for the Future

The last common reason that someone will recreate their home is to prepare for the future so they don’t have to do it later. These are only security precautions.

Why Is My Water Heater Making Noises?

Sediments gather around the tube of water heating elements. When the element dies, the sediments that are attached are trapped under the water, and the water heats up to produce a cracking or breaking sound when forced through the sediment. This is more common in older units, and noise increases when the deposit layer thickens. Clean or replace elements. Another indication that heaters need maintenance is roar, which is produced by sediments which are stirred by the flow of water in the tank. Use a limiting mixture to clean the tank and drain the water heater.

If maintenance does not cure the problem, noise may be something as simple as expansion and contraction of the main steel tank or expansion tank during normal operation. Metal pipes can make similar sounds in situations where heated water exceeds about 125 degrees.

I Don’t Have Enough Hot Water. How Long Should A Water Heater Last?

Look at the capacity of your water heater. Tank heaters generally only provide 2/3 of their capacity as hot water (this is because cold water enters the tank and melts it). So, a fully heated 50 gallon tank will produce around 33 gallons of hot water at a certain time. The average bath uses 2 gallons of water per minute, so the same 50 gallon tank is good for a little less than 17 minutes of hot water.

Tip: As a general guideline, you should aim for a tank capacity of 10-15 gallons per adult in your home.

My Drains or My Toilet Stinks. What Can I Do?

If your toilet is stinks, you can do this DIY to remove the smells:

  1. Pour 1/4 cup of baking soda into the gutter.
  2. Follow with one cup of white vinegar.
  3. Leave for two hours with the bathroom door closed.
  4. Slowly pour one gallon of hot water into the drain.
  5. After fifteen minutes, use cold water for ten minutes to rinse the vinegar clean. This step is very important, so don’t miss it.
  6. Pour ½ cup of chlorine bleach into the gutter and let stand for two hours with the bathroom door closed.
  7. Rinse with one gallon of hot water poured slowly.
  8. Allow cold water to flow for ten minutes. Now, enough water should be on the “U” curve of the P-trap.
  9. The final step is to pour four ounces of mineral oil (ordinary cooking oil will work in an emergency) to the sewer. Oil floats on water in a trap and slows evaporation.
  10. Optional: Use a screwdriver to release the trap if you want to replace it. You can also remove the trap to clean it.

What Can I Put Down My Garbage Disposal?

There are various questions about removing waste, one of which is what we can dispose of through disposal. But this is also influenced by how much engine exhaust power you have. To maintain good disposal, you should not throw away things like corn husks, onion skin, celery, bone, coffee powder, fats, and potato skin. Because these things have a strong structure and can accumulate in the disposal and clog the drainage pipe which can cause water to be blocked. In addition, the above things can also cause unpleasant odors such as fat.

In addition to food waste above, rubbish such as paper, metal, plastic, cigarette butts and wood are also advised not to be disposed of through disposal because clearly the above types of garbage will clog your disposal.

To maintain the cleanliness of the garbage disposal you have you can do:

  • Using ice and salt

Throw some ice cubes in the garbage dump and add with salt. after that give cold water and turn on the engine. This helps loosen the oil and debris left over in garbage disposal due to the rough texture of ice and salt.

  • Give Baking Soda and Vinegar

You can give 1 cup of baking soda to the garbage disposal and give 1 cup of vinegar to the disposal and there will be smoke coming out due to the chemical reaction of baking soda and vinegar. Baking Soda and vinegar help break down the remaining dirt in your garbage disposal.

Sister Sites

Call Us Now
Call Now
Directions